segfaults & readonly filesystem

[fulltilt]

hatte vorhin zum 2. mal innerhalb 2 Monaten ein filesystem problem:
readonly filesystem

nach dem fsck habe ich folgende logs gefunden:

Code:

kernel: awstats.pl[23725] general protection ip:7fbca65221f7 sp:7fffaea3b320 error:0 in libperl.so.5.10.0[7fbca64b3000+166000]
...
kernel: php5-cgi[10853] general protection ip:65b2e1 sp:7fff1e77d9a0 error:0 in php5-cgi[400000+506000]
kernel: imapd[2998] general protection ip:7f5a26eb8af0 sp:7fff2f9f3958 error:0 in libc-2.7.so[7f5a26e3e000+14a000]

könnte das auf eine defekte platte hindeuten?
Athlon 64 X2 5600+
6 GB DDR2 800
2 x 750 GB SATA II
ca. 15 Monate in Betrieb

[BeNe]

Hast Du keine S.M.A.R.T.-Tools auf dem Server am laufen ?
Installiere mal smartctl und liese mal die Platten aus.
Schickt Dir auch eine e-Mail falls eine Fehler auf einer Platte ist

Greez BeNe

[fulltilt]

noch nicht ...
reicht das aus:
apt-get install smartmontools

(10-07-2010 02:22 AM)BeNe Wrote:  Hast Du keine S.M.A.R.T.-Tools auf dem Server am laufen ?
Installiere mal smartctl und liese mal die Platten aus.
Schickt Dir auch eine e-Mail falls eine Fehler auf einer Platte ist

Greez BeNe

[BeNe]

Ja, das ist in der Sammlung dabei.
Hatte dazu mal was geschrieben --> http://www.deluxe-stylez.de/2009/06/30/d...r-t-prufen

Danach kannst Du mit smartctl die Platte auf Fehler auslesen.

Greez BeNe

[fulltilt]

Danke coole site
so läuft jetzt - beim manuellen check bekomme ich nur ein:
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.

ist das so richtig?

und das in der /etc/smartd.conf

Code:

/dev/sda  -m root@mymail.tld -M exec /usr/share/smartmontools/smartd-runner

(10-07-2010 02:46 AM)BeNe Wrote:  Ja, das ist in der Sammlung dabei.
Hatte dazu mal was geschrieben --> http://www.deluxe-stylez.de/2009/06/30/d...r-t-prufen

Danach kannst Du mit smartctl die Platte auf Fehler auslesen.

Greez BeNe

---

okay habs jetzt - für sata:
smartctl -a -d ata /dev/sda1

scheint aber nix auffälliges zu finden:

Code:

=== START OF INFORMATION SECTION ===
Device Model:     SAMSUNG HD752LJ
Serial Number:    S12UJDWS305940
Firmware Version: 1AA01113
User Capacity:    750.156.374.016 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   8
ATA Standard is:  ATA-8-ACS revision 3b
Local Time is:    Wed Oct  6 19:18:28 2010 CEST

==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details.

SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                 (11016) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 184) minutes.
Conveyance self-test routine
recommended polling time:        (  20) minutes.
SCT capabilities:              (0x003f) SCT Status supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   100   100   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0007   079   079   011    Pre-fail  Always       -       7120
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       25
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   100   100   051    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0025   100   100   015    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0032   098   098   000    Old_age   Always       -       11180
10 Spin_Retry_Count        0x0033   100   100   051    Pre-fail  Always       -       0
11 Calibration_Retry_Count 0x0012   100   100   000    Old_age   Always       -       0
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       25
13 Read_Soft_Error_Rate    0x000e   100   100   000    Old_age   Always       -       0
183 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       0
184 Unknown_Attribute       0x0033   100   100   000    Pre-fail  Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   060   060   000    Old_age   Always       -       40 (Lifetime Min/Max 40/40)
194 Temperature_Celsius     0x0022   060   060   000    Old_age   Always       -       40 (6 109 42 39)
195 Hardware_ECC_Recovered  0x001a   100   100   000    Old_age   Always       -       5787146
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   100   100   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x000a   100   100   000    Old_age   Always       -       0
201 Soft_Read_Error_Rate    0x000a   100   100   000    Old_age   Always       -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.