Danke coole site
so läuft jetzt - beim manuellen check bekomme ich nur ein:
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
ist das so richtig?
und das in der /etc/smartd.conf
Code:
/dev/sda -m root@mymail.tld -M exec /usr/share/smartmontools/smartd-runner
(10-07-2010 02:46 AM)BeNe Wrote: Ja, das ist in der Sammlung dabei.
Hatte dazu mal was geschrieben --> http://www.deluxe-stylez.de/2009/06/30/d...r-t-prufen
Danach kannst Du mit smartctl die Platte auf Fehler auslesen.
Greez BeNe
okay habs jetzt - für sata:
smartctl -a -d ata /dev/sda1
scheint aber nix auffälliges zu finden:
Code:
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG HD752LJ
Serial Number: S12UJDWS305940
Firmware Version: 1AA01113
User Capacity: 750.156.374.016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 3b
Local Time is: Wed Oct 6 19:18:28 2010 CEST
==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details.
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (11016) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 184) minutes.
Conveyance self-test routine
recommended polling time: ( 20) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 079 079 011 Pre-fail Always - 7120
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 25
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 11180
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 25
13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age Always - 0
183 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
184 Unknown_Attribute 0x0033 100 100 000 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 060 060 000 Old_age Always - 40 (Lifetime Min/Max 40/40)
194 Temperature_Celsius 0x0022 060 060 000 Old_age Always - 40 (6 109 42 39)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 5787146
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.