Rebuilding all customer configuration files Error 1.00 - 1.0.3

[Fastserv]

I get the following error when i try to update from 1.0.0 to 1.0.3

DEBUG: push_el() sub_name: exit_msg(), msg: Starting...

[failed]

FATAL: An error was occured during update process!
Correct it and re-run this program.

Via E-Mail i got the following:

A critical error just was encountered while executing function restart_httpd() in /var/www/ispcp/engine/ispcp-serv-mngr

Error encountered was:

========================================================================
Apache config file is corrupted. Please check before restarting Apache server!!!


Stefan

[datacompboy]

What OS? What apache version?
Have you looked in httpd.conf (and included files)?
Have you tried to start apache and check file syntax?

[Fastserv]

(12-24-2009 02:28 AM)datacompboy Wrote:  What OS? What apache version?
Have you looked in httpd.conf (and included files)?
Have you tried to start apache and check file syntax?

Sorry!

Debian Etch
Apache 2.2.3

Error was a the syntax error "MaxRequestsPerProcess 500" in fcgid_ispcp.conf

After i commented this line out apache runs, but im not sure if the ispcp update skript went thru the hole process. Of course every time i re run the skript the error comes back.

Stefan

[datacompboy]

have you installed latest updates, including security before update?

[Fastserv]

(12-24-2009 02:45 AM)datacompboy Wrote:  have you installed latest updates, including security before update?

Sure

[datacompboy]

http://isp-control.net/forum/thread-8847-page.html
well, trouble is in fcgid version.

Try to install latest libapache2-mod-fcgid from etch-backports
http://packages.debian.org/ru/source/etc...-mod-fcgid

[Fastserv]

Thank you.

The Forum Link is wrong. I try to install the backport version.

Stefan

[Nuxwin]

Hello ;

yes, the fcgid module for etch is 1.10. This version does not support the "MaxRequestsPerProcess 500".

http://isp-control.net/forum/thread-8847.html

[Fastserv]

Thank you. The Backport fcgid did the job.
Installation went fine.

Stefan

[Alex Joe]

I've got the same problem, but in Debian Lenny 5.03. I've update OS to newest version (all packages).

Quote: ispCP PMA configuration file:DEBUG: push_el() sub_name: setup_gui_pma(), msg: Starting...
DEBUG: push_el() sub_name: get_file(), msg: Starting...
DEBUG: push_el() sub_name: get_file(), msg: Ending...
DEBUG: push_el() sub_name: setup_gui_pma(), msg: Ending...
[done]
DEBUG: push_el() sub_name: rebuild_gui_cfg(), msg: Ending...

Rebuilding all customer configuration files
Please wait, this may take some time:DEBUG: push_el() sub_name: rebuild_customers_cfg(), msg: Starting...
DEBUG: push_el() sub_name: doSQL(), msg: Starting...
DEBUG: push_el() sub_name: doSQL(), msg: Ending...
DEBUG: push_el() sub_name: doSQL(), msg: Starting...
DEBUG: push_el() sub_name: doSQL(), msg: Ending...
DEBUG: push_el() sub_name: doSQL(), msg: Starting...
DEBUG: push_el() sub_name: doSQL(), msg: Ending...
DEBUG: push_el() sub_name: doSQL(), msg: Starting...
DEBUG: push_el() sub_name: doSQL(), msg: Ending...
DEBUG: push_el() sub_name: doSQL(), msg: Starting...
DEBUG: push_el() sub_name: doSQL(), msg: Ending...
DEBUG: push_el() sub_name: doSQL(), msg: Starting...
DEBUG: push_el() sub_name: doSQL(), msg: Ending...
DEBUG: push_el() sub_name: doSQL(), msg: Starting...
DEBUG: push_el() sub_name: doSQL(), msg: Ending...
DEBUG: push_el() sub_name: doSQL(), msg: Starting...
DEBUG: push_el() sub_name: doSQL(), msg: Ending...
DEBUG: push_el() sub_name: sys_command_rs(), msg: Starting...

And script stopped, no error messages.

Alex Joe